Nexus MT / MTM
5" Two-Way Bookshelf Speakers
5" Two-Way Bookshelf Speakers
These designs can put out a lot of sound for their size. The DS135 is capable of running fullrange in a small ported enclosure (0.15-0.25cuft) tuned to 55-65hz if playback volume is limited to prevent over-excursion but is best used with a highpass and subwoofer to really stretch it's legs.
My original test enclosure for the TM design was about 0.15cuft, 6"w x 9"h x 8.5"d tuned to 60hz with the 1-3/8" adjustable port from PE. However in 2018 I redesigned the enclosure which is now 7"w x 10"h x 9.25"d, built from 1/2" MDF with a 3/4" baffle, using the 1-5/8" flared port (260-474) from Parts Express (port left at full length). I have the port installed on the back directly behind the tweeter for both this design and the MTM.
The crossover is about 2100hz om both designs, fairly low but the ND28 handles it well. The low crossover and tight driver spacing allows this design to work quite well as a nearfield monitor with very little distance needed for proper summation between the drivers. It also allows a decently large vertical listening window. Don't let the nearfield comment scare you away from using it in a larger listening space, with a highpass filter at 80hz it will handle the full power of most AVR's and provide enough output to satisfy most people.
The MTM cabinet is 7"w x 16"h x 10.5"d (built from 1/2" material and 3/4" baffle). It uses the 2-1/2" flared port tube (260-478) from parts express cut to 6" overall length. The bass output pair of those woofers can produce is quite impressive considering the size of the enclosure. The MTM has the advantage of a reduction in distortion from the bass up through the midrange from the use of two woofers handling the content vs. the single woofer in the TM design.
I chose to add a decent amount of BSC into these designs which gives them a very full sound. The midrange is very clear but not overbearing, and the treble smooth without sounding dull. Bass is again very good for such a compact speaker.
Crossover Parts List:
C1 10uF (Poly) - C2 3uF (Poly) - C3 22uF (NPE) - C4 0.47uF (Poly) - C5 68uF (NPE) - C6 6.8uF (NPE)
L1 1.5mH (18AWG I-core) - L2 0.60mH (20AWG Air core) - L3 0.40mH (18AWG Air Core)
R1 10 Ohm (10w Wirewound) - R2 15/16 Ohm (10w Wirewound)
Optional set of crossover PCBs available for the Nexus MT
If you are using a class D amplifier you may want to add an ~8-20 ohm resistor in series with the C4 capacitor. This will not change the frequency response of the speaker but prevents issues from arising due to a capacitive load in the ultrasonic range which some switching amps do not like. This resistor can be small anything over a 1 watt rating should work.
Nexus MT Cabinet Custlist:
Using 1/2" material for the cabinet and 3/4" for the baffle.
Overall Cabinet Dimensions - 10"H x 7"W x 9"D
Baffle(3/4") / Back (1/2"): 10" H x 7" W
Sides (1/2") x2: 10" H x 7.75" W
Top/Bottom (1/2") x2: 7.75" L x 6" W
If using a window style brace, same size as top/bottom.
Using 3/4" material for entire cabinet.
Overall Cabinet Dimensions - 10"H x 7"W x 10.5"D:
Baffle/Back (3/4") x2: 10" H x 7" W
Sides (3/4") x2: 10" H x 9" W
Top/Bottom (3/4") x2: 9" L x 5.5" W
If using a window style brace, same size as top/bottom.
Crossover Parts List:
C1 15uF (Poly) - C2 6.2uF (Poly) - C3 4.0uF (Poly) - C4 0.68uF (Poly) - C5 50uF (NPE)
L1 1.0mH (18AWG I-core) - L2 0.25mH (20AWG Air core)
R1 5 Ohm (10w Wirewound) - R2 40 Ohm (10w Wirewound)
Optional crossover PCBs available for the Nexus MTM
If you are using a class D amplifier you may want to add an ~8-20 ohm resistor in series with the C4 capacitor. This will not change the frequency response of the speaker but prevents issues from arising due to a capacitive load in the ultrasonic range which some switching amps do not like. This resistor can be small anything over a 1 watt rating should work.
Nexus MTM Cabinet Cutlist:
Using 1/2" material for the cabinet and 3/4" for the baffle.
Overall Cabinet Dimensions - 16"H x 7"W x 10.5"D
Baffle(3/4") / Back (1/2"): 16" H x 7" W
Sides (1/2") x2: 16" H x 9.25" W
Top/Bottom (1/2") x2: 9.25" L x 6" W
If using a window style brace, same size as top/bottom.
Using 3/4" material for entire cabinet.
Overall Cabinet Dimensions - 16"H x 7"W x 12"D:
Baffle/Back (3/4") x2: 16" H x 7" W
Sides (3/4") x2: 16" H x 10.5" W
Top/Bottom (3/4") x2: 10.5" L x 5.5" W
If using a window style brace, same size as top/bottom.