Nexus MTMWW
Dual 8" Three-Way Tower Speaker
Dual 8" Three-Way Tower Speaker
The Nexus MTMWW tower is the capstone design when it comes to the Nexus lineup. These are the format I was most excited to build and I started with the full intention to fully finish out a pair of cabinets for personal use.
I did build my pair just in time to bring them to the 2014 Parts Express Midwest Audiofest where they placed 3rd in the Dayton Audio category on a pair of crossovers which I only had a couple days to tune after finishing the cabinets. I did end up making some significant changes to the crossover after the event when I had more time with the finished pair. In fact these went through a number of crossover updates over the years, more then the other Nexus designs since I spent much more time listening to these. However the last crossover update was in 2018 and I doubt I will change things further as that version is what I have in them now and they are still a joy to listen to even today (2026).
The Dayton SD215 woofers give very well rounded bass in these large ported tower cabinets, deep extension well below 30Hz but nice punchy upper bass as well. The midrange is clean and detailed, the dual drivers let you really open these up without any hint of strain or compression. Finally the ND28 is a nice clear tweeter that does an excellent job considering it's cost, the larger 1-1/8" diaphragm allows it to keep up with the dual woofer and midrange drivers fairly well when you push things and it blends exceptionally well. I can say these have no trouble running full range powered by a 200w/channel amplifier and with sensitivity approaching 90dB they should have plenty of output for most even in fairly large rooms. Overall this design is still one of my favorites for 2-channel playback, it just does well with most types of music with a full authoritative bass response and nice articulate and wide soundstage with solid imaging. There is nothing that I can point to and say is lacking.
You can technically use this design and build a larger WMTMW center channel, though I have not done any additional testing for that cabinet format.
Cabinet Design
The cabinets for the Nexus MTMWW are 46" Tall x 10" Wide x 15" Deep using 3/4" thick material excluding the additional base/foot seen in my photos which is 12" x 17" and 1.25" thick (1/2" + 3/4"). This resulting cabinet volume for the woofers is roughly 2.5cuft. I used a 4" precision port kit trimmed to 12" overall length (6" center tube) which tunes the cabinet to ~28Hz.
The midrange chamber is small, it runs the internal width of the cabinet and the depth of that chamber is 3" (internal) which gives about an inch of clearance behind the midrange magnets. The height of that chamber is 14.75".
The angle on the back of the cabinet is mostly for appearances as I wanted to do something a bit different with these then just a regular rectangle. If you want to cop it that angle starts at the top 10" back from the baffle and runs down to 30.5" high. The cabinet can certainly be built without the angled back just a regular rectangular shaped cabinet if desired, no real change in performance.
There is window bracing above/below and in-between the two woofers. The midrange chamber itself acts as horizontal bracing to the top part of the cabinet but there are a couple braces running front to back inside the mid chamber (between the two mids and tweeter) and there should be a brace placed behind center of that chamber to the rear wall as well I just forgot to add that on the 3d model.
The walls of the woofer chamber should be lined with 1 - 1.5" thick damping material. I also filled the top portion of the cabinet behind the midrange chamber with polyfill. I also placed polyfill in the lower chamber (below the bottom brace) around the the port tube but kept the area near the internal flare clear. The wall directly in front of the internal flare does not get any damping material either as you do not want to restrict airflow from the port. The midrange chamber should be filled with polyfill or other suitable damping material like cotton, rockwool or fiberglass insulation leaving just enough room to install the drivers.
Nexus MTMWW Tower Cabinet Cutlist (Rectangular cabinet, no sloped back):
Sized for 3/4" cabinet material, Overall cabinet dimensions - 46"H x 10"W 15"D (not including baseplate/feet):
Baffle (3/4"): 46" H x 10" W
Back (3/4"): 46" H x 8.5" W
Sides (3/4") x2: 46" H x 14.25" W
Top/Bottom (3/4") x2: 13.5 L" x 8.5" W
Window Brace (3/4") x3: 13.5" x 8.5" - Two should be full window braces and are placed below/between the woofers, the third above the woofers forms the bottom of the midrange chamber and should only have openings behind that chamber.
Internal Midrange Chamber Back Panel (3/4") x1: 14.75" H x 8.5" W.
Another window brace could be added behind the midrange chamber, in this case it would be: 9.75" x 8.5", otherwise you can add stick bracing there.
Driver centers measured fractionally down from the top: 3-11/16", 7-7/8", 11-1/16", 20-1/2", 29-1/2". The port center should be 6-1/8" measured up from bottom of cabinet.
Some additional images below showing the initial cabinet dry fit and the how I had installed the damping material. The damping photos were taken when I had to strip the original adhesive vinyl finish I used off one cabinet after it had bubbled badly from being left in a hot car in the sun on the way back from Midwest Audio Fest. I installed the crossover on the side of the cabinet behind one of the woofers which is faintly visible in the photo. Wires for the midranges and tweeter are run through a small hole drilled through the midrange chamber which is sealed after they are run.
Crossover Design
The crossover is nearly the same topology as the other 3-way center channel design.
A simple 2nd order highpass with a bit of damping is all that's needed to for the easy to work with ND28 tweeter.
The midrange uses a simple 1st order highpass at the woofer crossover point, the lowpass is 3rd order to provide the correct shaping needed in the band-pass configuration, R2 is there to help soften the lowpass knee and C3 acts as a tank filter to provide some additional slope to the lowpass and suppress cone breakup. Finally a pair of resistors out front for power handling drop the level of the parallel midrange drivers in line with that the woofers/tweeter.
The woofer highpass is mostly 2nd order but the addition of L2/R1 just provide a little more slope and a softer knee which helps with the response shaping more then a purely 2nd order filter would achieve.
Note: Inverted polarity on the midranges and tweeter.
The woofer dual voice coils should be wired in series then the two drivers wired in parallel to the crossover. The midrange drivers should be wired in parallel.
Crossover Parts List:
C1 100uF (NPE) - C2 39/40uF (Poly) - C3 0.68uF (Poly) - C4 12uF (Poly) - C5 4.3uF (Poly)
L1 4.0mH (18awg I-Core) - L2 0.1mH (20awg Air Core) - L3 1.0mH (20awg Air Core) - L4 0.40mH (20awg Air Core) - L5 0.40mH (20awg Air Core)
R1 0.5Ohm 10w - R2 1.0 Ohm 10w - R3 2 Ohm 10w - R4/R5 5 Ohm 10w
Other brands with equivalent value and similar dimensions can also can also be used.
Additional Photos: