AlTi
a DIY 2-way bookshelf speaker design
a DIY 2-way bookshelf speaker design
This design can use HiVi M5N (above) or M5N-B (below).
Parts List:
Woofer:
Tweeter:
Port Tube:
C1 - C4 designed to be Poly caps, C5/C6 sized for NPE.
C1(4uF) - C2(1.5uF) - C3(0.22uF) - C4(12uF) - C5(80uF) - C6(22uF)
L1/L3 should be 20AWG air core, L2 should be 18AWG I-core or equivalent.
L1(0.4mH) - L2(1.5mH) - L3(2.0mH)
Resistors should be at least 10w, standard 5% tolerance wire-wound or better are perfectly suitable.
R1(8 Ohm) - R2(7 Ohm) - R3(20 Ohm) - R4(10 Ohm)
PCB is designed to fit the parts linked above but others components of equivalent value with similar dimensions can be used as well.
The AlTi is an inexpensive 2-way bookshelf design using the aluminum cone HiVi M5N midbass and Dayton DC25T-8 titanium dome tweeter. You can probably guess how I arrived at the AlTi name.
This is a design evolved out of another very similar design I built as a wedding gift that had used some buyout paper cone where I used the DC25T-8 tweeter for the first time. I liked how that design sounded and was especially pleased with the tweeter so I was on the hunt for an off the shelf woofer which would work in the design so that others could build the speakers if they wanted to.
The M5N had T/S specs which allowed it to work well in the same enclosure size and the frequency response also looked good. Best of all it had an identical frame diameter and dropped right into the cutouts I had made for the buyout woofers so I was able to do some preliminary testing in the original enclosures before handing them over.
As I said I really like how the DC25T-8 sounds, it's detailed without being harsh and blends exceptionally with the M5N. Most inexpensive soft domes that I have used around this price point tend to get a little stuffy at higher output levels but these remain remarkably clear. Bass response is decent with the predicted f3 of just about 50hz in this enclosure, I measured it a little higher then that but my tuning also came in a little low. This allows them to be enjoyable enough for most music without using a sub at modest volumes. The rated 2.7mm xmax is real however, the woofer certainly has clean mechanical travel past this point but any exceptionally heavy bass notes will start to modulate the midrange output as the coil moves out of the gap. Use with a highpass and subwoofer is best for higher playback levels, though it still struggles as you near 100dB/1m. Plenty for casual listening at decent levels buy don't expect these to rock the house with an single 5" woofer.
*(When originally designed in 2017.)
Crossover Details
The crossover is approximately 2.6khz, 2nd order on both tweeter and woofer. C2 on the tweeter providing some minor contouring in addition to the two resistors providing padding as well. The woofer side has C3 acting as a notch filter to suppress the cone breakup while the two parallel filters are there to even out response lumps from the baffle step and diffraction.
If you are using a class D amplifier you may want to add an ~8-20 ohm resistor in series with the C3 capacitor. This will not change the frequency response of the speaker but prevents issues from the capacitive load in the ultrasonic range which some switching amps do not like. This resistor can be a smaller 5w resistor to save space.
Nominal impedance of the drivers is 8 ohms but with the crossover does dip to just above 4 Ohms between 200-300hz so you will want a decent amp if you want to drive these hard. If performing light playback an amplifier rated for 8 ohms should be fine.
On axis the tweeter's response is decently smooth out past 20k though when moving off axis and the phase shield does cause some extra rolloff at the top end and a notch between 13-14k but it really isn't an issue until you get more then 20 degrees off axis.
There is a slight dip in the response of ~1dB between 3-4k directly on axis however this flattens out slightly when you move off axis and I found leaving it sounded better as it gives a smoother power response.
Note this crossover sim is using gated indoor measurements so low frequencies are not accurate.
Cabinet Details:
The enclosures I built for these are 11.75" high x 8" wide x 10" deep, I used 3/4" edge glued baltic birch panels that were on clearance at my local hardware store but MDF or quality plywood is just as suitable. Tuning in the 0.3cuft net enclosure ends up in the low 50's, I measured ~47hz with a 3/4" MDF flare added to the inside port termination of the 1-7/8" flared port that PE sells. Without that flare the tuning will be a tad higher should actually give a flatter bass response.
Cut List for the enclosure using 3/4" thick material,
Front and rear baffle: 11.75" x 8"
Sides: 11.75" x 8.5"
Top/bottom: 6.5" x 8.5"
Window Brace: 6.5" x 8.5"
The tweeter and woofer are positioned so the top/bottom edge of their frames are ~1" from the top and bottom of the enclosure. This equates to the tweeter center being 2-15/16" down from the top of the enclosure and the woofer center being 3-13/16" up from the bottom of the enclosure. The rear port is positioned so that it is centered behind the tweeter, the same 2-15/16" down from the top to the center applies there.
The woofer OD is 5-11/16", ID or inner cutout is 4-9/16" and mounting flange is 5/32" thick (for flush mounting).
The tweeter OD is 3-15/16", ID is 2-7/8" and mounting flange is also 5/32" thick. You do need to make small cutouts for the terminals on this tweeter.
The port cutout is 2-11/16", I can't remember how it fits at that size it may need to be opened up slightly since the port is press fit. I usually cut slightly small and slowly open it up with a file or sandpaper to get a nice friction fit.
For enclosure damping I used R6.7 ultratouch recycled denim for mine (one 48" long roll is perfect for two speakers) though poly batting or acoustic foam of similar thickness should also suffice. I lined the side walls and the bottom and rear of the cabinet leaving an open space for the crossover near the bottom back.